The Warm Audio Centavo is an accurate recreation of the most sought-after overdrive pedal of the 90's and beyond. Whether you're after the fabled clean boost tones, transparent overdrive, or you want to push your dirty channels to true grit, the Centavo has all of the adored tones of the vintage box. In addition, the Warm Audio Centavo has the infamous “MOD” selectable on the back. When in the “up” position, low-end response on the bottom strings is extended. With a true-to-original, custom-cast golden enclosure & all the signature sounds of the original, Centavo delivers an authentically legendary pedal experience.
MORE»
| List | $179.00 |
The Tensor(TM) gives you live reverse and tape stop effects, pitch shifting, time stretching and hold functions that you can combine in creative ways. Slow down, speed up and rewind in real time. Stretch or compress time with no pitch change. Loop, overdub, and randomly slice phrases up to 9.4 seconds (4.7 seconds in stereo).
Intelligent randomization adapts to the knob settings. The results range from occasional CD skips, stutters, and rhythmic repeats to random slicing and erratic pitch shifts. Both foot switches have momentary and latching modes to inject pitch jumps, glitches, or instantly rewind what you just played.
The Tensor(TM) is in a pedalboard-friendly enclosure with all jacks on top. All controls are immediately accessible with well-spaced knobs for live tweaking, and USB MIDI for recording and sequencing.
Features:
• Tape speed from reverse to stop to forward
• Realtime time stretch up to 4:1
• Loop time compression and stretch from 1:4 to 4:1
• Pitch shift from -2 to +2 octaves
• Intelligent randomization
• Overdub, replace, and dual buffer (next) loop modes
• Forward/alternate/reverse loop direction
• Additional looping functions via remote switch or MIDI
• Momentary or latching foot switches
• Assignable expression pedal, remote switch, remote tap, or MIDI port
• +5.5 dBu maximum input level (adjustable to +8 dBu)
• Stereo input/output (TRS)
• MIDI (USB and TRS)
• Web-based editor for editing presets and accessing hidden parameters
MORE»
| List | $329.00 |
Particle™ is a granular delay/pitch shifting pedal. It chops your signal into small grains and then rearranges, shifts, and mangles it, using the techniques of granular synthesis in real time. Results range from radical pitch and delay modulation to shimmering repeats to time stretching, stutter, and glitch sounds.
Five delay and three pitch modes give intuitive control over random delays, bubbling textures, time stretching, and rhythmic glitches. Take a unique approach beyond conventional delay, pitch, flanging, and chorus sounds. Freeze notes with adjustable threshold for stutter, punch in, or drone-line effects. Lock multiple parameters to tap tempo or MIDI sync with independent note divisions for intricate rhythms. Access all parameters via MIDI, tablet, or “modeless” front-panel operation for full control over granular processing.
The Particle 2 is performance friendly, with controls spaced for real-time tweaking and designed so you can explore new sonic territory while remaining in control. Use the assignable expression pedal or DIY-friendly remote switch for hands-free control. The Particle 2 is pedalboard-friendly with all jacks on top. With full MIDI control, stereo input/output, and +8 dBu maximum input level, it is also at home in modular setups or the studio.
Features:
• 3 pitch modes: detune, density, LFO
• 5 delay modes: random, density, LFO, random pitch, reverse
• Adjustable grain size and density
• Pitch shift +/- 1 octave
• Delay 0-2.5 seconds
• Feedback with adjustable lowpass filter
• Auto-freeze/stutter with adjustable threshold
• Tap tempo/momentary freeze footswitch
• Independent tap divisions for delay time, grain size, grain density, and LFO
• Soft touch bypass (momentary or latching), user replaceable
• Stereo input/output (TRS)
• Assignable expression pedal, remote switch, remote tap, or MIDI port
• Additional parameters via MIDI (USB or TRS)
• MIDI clock synchronization
• Presets (4 on front, 127 via MIDI)
• Web-based editor for editing presets and accessing hidden parameters
Designed and assembled in USA. Requires a 9V 250 mA center negative power supply (not included).
MORE»
| List | $329.00 |
The Warmdrive is a true reproduction of a highly revered pedal known for delivering the tones of an unattainable overdriven amp. The original pedal is known to go from silky-smooth tones reminiscent of a special overdriven amp at the sweet spot, all the way to sustain-rich distortion. The Warmdrive combines carefully-selected components & true-to-original circuit design to achieve the same tone and sonic profile of the legendary pedal. The “secret sauce” of the Warmdrive, just like the original, is the unique voice/tone control combination on the stomp box. Giving artists extra versatility, this control allows the player to modify the frequency both before (Voice control) and after (Tone control) the clipping stages.
MORE»
| List | $149.00 |
The Next Gen of a Classic
Soul Press II is a next-gen product in the Hotone Press series pedal line. It's new-designed upgrade based on the popular concepts of both the Soul Press and Vow Press. It integrates up to four function modes (volume, wah, volume/wah, expression), taking playability to new heights. The pedal position indicator shows the pedal position in real time. The TONE mode selection and Q value adjustment represent an absolute improvement in tone and functionality. Multiple I/O options provide more diverse access. The reimagined pedal size maintains portability while delivering an optimal ergonomic experience. Soul Press II is a truly versatile wah pedal.
MORE»
| List | $119.99 |
Pro level quality at an entry level price. The new Mini Classic Switchless Wah comes equipped with the great features our Wah pedals are known for, all for just $99. Yes, you read that correctly! Just $99. You get classic Wah-Wah tone with our MQ2 Inductor, dependable Electro-Optical circuitry, smooth and easy Switchless activation, and our True Tone Bypass Buffer circuitry.
Features include:
• Switchless operation – simply step on the treadle to engage the Wah and step off to bypass
• Engineered to save space on your board
• World famous Electro-Optical design
• Classic Wah tone with a custom MQ2 Inductor
• True Tone Bypass buffer circuit ensures pure guitar tone and output
• Glow-in-the-dark treadle rubber and Morley logo
• Powered by one 9-volt battery or optional Morley 9V adapter
• Rugged cold-rolled steel housing, LED indication, quick clip battery door and one-year warranty
• Works with Guitar, Bass or Keys
MORE»
| List | $129.00 |
The hard-clipping, op-amp-based circuit of the ODD (Over Drive Disorder) delivers all of the sounds of a cranked, saturated tube amp made famous in legendary recordings. True to its inspiration, the ODD is perfect for adding a little breakup to an otherwise clean tone, or dramatically transforming your clean pedal-platform amp into a punk-rock powerhouse. To accurately deliver this popular modern tone, the ODD is built like an iconic pedalboard staple with through-hole construction using premium components, including a TLO82CP Op-Amp, 2N7000 transistors, & hand-selected capacitors & resistors.
Featuring classic-inspired controls & sounds, including a UK/US Switch, the ODD can quickly flip personalities. Engaging the UK setting distorts earlier, bumps the upper-mids, and increases volume – giving this setting more of a cranked, “chimey” amplifier tone. The US setting has a little more clean headroom, allowing the ODD to act more like a boost at first, and better aligns with traditional tweed-based “edge of breakup” amplifier tones.
MORE»
| List | $119.00 |
The Warm Audio Mutation Phasor II is an accurate recreation of a swirly phaser made famous in the experimental era of the 1970s. Mutation Phasor II has all of the vintage vibes of the original phaser pedal allowing you to add depth, wobble, swirl, or “instant funk” to guitar, keys, bass, or anything you can dream of. This electro-optical phase-shifting pedal is built with a true-to-original recreation of the 70s circuit using premium components. True to the original pedal, Mutation Phasor II delivers all the rich depth and instant psychedelic tones, favored by innovative musicians and producers like Billy Corgan, Tom Bukovac, Robin Trower, and many more.
Tech Specs
• Electro-Optical Phase-Shifting Pedal With Feedback Circuit
• Phasing Rate: .1Hz - 18Hz
• Premium Components, Including RC4558P Op-Amps, Various Vintage-Style Diodes, and Hand-Selected Film Capacitors & Carbon Resistors
• Controls: Rate, Depth, and Feedback
• Frequency Response: 20Hz - 20KHz
• Min Feedback: 4V RMS, 11.2V Peak-to-Peak ¦ Max Feedback: 2V RMS, 5.6V Peak-to-Peak
• Signal-to-Noise Ratio: 86 dB Below 2V Input
• Current Draw: 150 mA
• Buffered Bypass
• 9-Volt Battery Or External 9V Regulated DC Adapter (center-negative)
Popular Uses
• Deep, Phase-Shifting Electric Guitar Tones
• Swirling, Psychedelic Modulated Keys
• Funky. “Wobbly” Base Lines
MORE»
| List | $149.00 |
The first in the Mako series, the D1 is a powerful multi-function delay with five, studio grade, high-fidelity, custom tuned programs. The programs are Digital, Mod, Vintage, Dual and Reverse. Each can be tuned and tweaked with modulation, tone, age, and subdivisions. The attack knob adds another dynamic to each program, opening up a new world for creating soundscapes. The D1 boasts stereo in and out, midi control and on-board presets. A workhorse of a delay that is just as ready for the road as it is the studio.
Each program can be fully customized to your taste and playing style with the Tweak knob. Flip the toggle switch to Mod to bring in a tasteful modulation to your delay trails. Tone will brighten or darken your delay trails. Age will add some grit and wear reminiscent of vintage delay units. Subdivisions can be easily changed between quarter, eighth and dotted eighth.
The Attack knob will soften the attack of the echoes. Dreamy and ethereal soundscapes can be created with higher repeat and attack settings.
Specs:
• The D1 comes in an anodized silver finish with black, dark green, red, orange and purple ink.
• The enclosure's exact size with knobs is 4.9-inches xx 2.52-inches x 2.64-inches
• Power requirements are 9VDC (300mA minimum)
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals. Daisy chain power supplies are not recommended. Power supply not included. MORE»
| List | $299.00 |
The HX Stomp XL delivers HX® modeling in a performance-ready pedal with eight capacitive-touch footswitches. The same SHARC® DSP chip found in Helix® enables it to run up to eight processing blocks simultaneously, and the footswitches let you access and control those blocks in powerful ways. It sends and receives Program Change, Continuous Controller, and other MIDI messages. USB HX Stomp XL functions as a multi-channel 24-bit/96kHz audio interface for Mac and PC, with DI, re-amping, and MIDI capabilities built in. HX Stomp XL can also record to an iPad (with optional Apple Camera Connection Kit).
MORE»
| List | $949.99 |
With its simple plug-and-play interface, ultra-portable lightweight design, and best-in-class tones, the POD® Go guitar processor gets you on the road to ultimate tone.
POD Go enables a simple and intuitive workflow. Choose, edit, and control sounds using the large color LCD screen, five push encoders, eight rugged footswitches, and cast-aluminum multi-function expression pedal–and add two external footswitches or a second expression pedal for even more real-time control. All the essential audio connections are at your fingertips, too, including balanced stereo outputs, a duplicate amp out that can be tapped before the Cab/IR, a stereo effects loop, a headphone jack, and even a USB port for accessing the 4-in/4-out audio interface with re-amping.
POD Go boasts an arsenal of professional-quality amp, cab, and effect models drawn from the acclaimed HX family of effects processors–including classic amps like the Blackface, Plexi Lead, and Treadplate–as well as supporting third-party IR loading. What is more, sophisticated features such as Snapshots enable you to easily access all the tones you'll need to cover every section of every song. With POD Go, you won't just take the stage–you'll own it!
• Best-in-class performance
• Simple interface with large color display
• Compact, ultra-portable lightweight design
• 270+ HX and legacy amp and effects models
• Third-party IR loading
• Stereo effects loop and Expression Pedal/Footswitch input
• Free POD Go Edit app
MORE»
| List | $669.99 |
HX Stomp™ is a professional-grade multi-effects processor that delivers the sound of Helix® amps, cabs, and effects in an ultra-compact pedal. Use it as a “super stompbox,” a backup or travel rig, an add-on tone expander when combined with other modelers, an audio interface – or even a complete guitar or bass rig. The same HX Modeling technology that powers the flagship Helix guitar processor enables HX Stomp to run up to six processing blocks simultaneously, making it the most powerful and flexible stompbox-sized multi-effects processor available. HX Stomp is easy to operate, however, thanks to its simple-but-powerful controls, 320 x 240-pixel color LCD, and capacitive-sensing footswitches with color-coded LED rings. External control via MIDI and optional expression pedal and footswitch control provide additional flexibility, as does I/O that may be configured for sophisticated routing such as simultaneously feeding an amp and a FOH mixer, 4-cable method operation with an amplifier, and studio re-amping. Along with over 300 amps, cabs, and effects – even a looper – HX Stomp includes a legacy library of effects from Line 6® M-Series pedals, as well as from classic Line 6 stompbox modelers such as the DL4™, MM4™, FM4™, and DM4™. There are also presets created specifically for bass players, as well as individual bass amp and cab models. The free HX Edit app offers preset librarian functionality and third-party IR loading.
• Utilizes the same HX Modeling as Helix
• Over 300 effects and models from Helix, M-Series, and legacy Line 6 products
• Up to 6 simultaneous amp, cab, and effect blocks (including a looper and IR loading)
• 3 capacitive-sensing footswitches with color-coded LED rings facilitate fast editing
• TRS dual expression pedal/footswitch input extends creative control capabilities
• Stereo effects loop (mono/stereo TRS send + stereo returns) facilitates use with other pedals
MORE»
| List | $699.99 |
The new Foxy Tone Box from Warm Audio is a hyper-accurate recreation of one of the most sought-after and beloved fuzz pedals of all time – used in the early seventies by legendary tone masters Billy Gibbons and Peter Frampton, and in the present day by folks like Adrian Belew, Nine Inch Nails and Beck. Covered in thick velvet just like the vintage pedal, the Warm Audio Foxy Tone Box faithfully recreates the vintage circuit and brings you the huge tone, octave-up sounds and look of the original...without having to pay crazy vintage prices!
MORE»
| List | $149.00 |
The Raster is a 1600 ms digital delay with a pitch and frequency shifter integrated into the feedback path. Forward or reverse delay can be shifted once or have continuously shifted repeats. Three delay ranges allow you to precisely dial in resonant feedback and instantly change delay time with rhythmic shifts. The feedback control has infinite repeats at 3 o'clock and chaotic, textured feedback loops at higher levels. Knob responses are carefully tuned for exploration of self-oscillation and feedback on the verge of blowing up. A tone control sweeps from dark analog-style repeats to digital clarity and emphasizes the attack at higher settings. The left and right delay times can be set as a ratio, so a single knob changes both in sync. The two delay channels can be arranged in series, parallel or ping pong.
Three pitch and frequency shifting algorithms are integrated into the feedback loop. Pitch shifting repeats up or down in semitone steps creates tempo-synced arpeggios and alien organ sounds. The detune setting can dial in micro pitch shifts and chorused repeats. The frequency shifter creates flanger-like textures and radical dissonant echoes. The left and right channels can be shifted by the same amount, a ratio, or opposite directions. At subtle settings, repeats evolve in a way that sounds natural, but different from analog delays.
The Raster's modulation section has seven waveforms that can be assigned to delay time, pitch shift, or effect level (for tremolo). There are two random waveforms for glitchy sliced delays or random pitch shift, wow and flutter, and broken tape deck effects. Envelope and inverse envelope enable dynamic flanging and pitch bent delays. Stereo controls adjust the modulation amount and phase between channels, for subtle shifts or swirling psychedelic washes.
The Raster 2 is performance friendly, with 6 knobs and 9 switches. The original Raster was praised for its knob response and immediacy, and the Raster 2 maintains that simplicity while adding flexible modulation and extensive stereo functionality. Alternate knob settings are related to the primary knob function, labeled, and off at the center position. Both footswitches can be latching or momentary, for instant pitch jumps or quick blasts of echo. The bypass switch can also mute the output in bypass while always listening, to catch, repeat, and manipulate what you just played.
The Raster is designed and assembled in Plymouth, MI, USA.
MORE»
| List | $329.00 |
The Bitmap(TM) is a stereo bitcrusher with fractional bit reduction and sample rate modulation. The Bitmap 2 adds waveshaping, wavefolding, and a window comparator for extreme digital distortion. A drive control handles everything from single coil guitars to synthesizers, with +8 dBu maximum signal level and plenty of gain with overdrive. Modulation and envelope control create dynamic, responsive distortion and digital artifacts.
The Bitmap 2 is tuned to provide maximum sustain without sputtering on staccato notes. Less extreme settings add layers of nonlinearities that interact in subtle ways, giving you the warmth and grit of 8- and 12-bit samplers. Sample rate reduction turns your guitar into 8-bit video game sounds or twists scales into inharmonic melodies. Sample rate modulation adds subtle motion or morphs your guitar into entirely new textures.
The Bitmap(TM) works with guitar, bass, synthesizers, drum machines, and other instruments or line level sources. A web-based editor allows you to edit presets and access additional parameters and modulation destinations.
Features:
• Fractional bit reduction from 24-bits down to 1-bit
• Sampling rate reduction from 48 kHz down to 110 Hz
• Sample-rate modulation with triangle, square, and random waveforms
• Adjustable wavefolding and waveshaping functions
• Mix control to maintain bass or add subtle crushing
• Envelope control over sampling rate or mix
• Drive control to accommodate single or dual coil pickups and line-level signals
• 4-pole lowpass filter
• Stereo input/output (TRS)
• Soft touch bypass (momentary or latching), user replaceable
• Aux. footswitch assignable to tap tempo or preset selection
• Assignable expression pedal, remote switch, remote tap, or MIDI port
• Additional parameters via MIDI (USB or TRS)
• MIDI clock synchronization
• Presets (4 on front, 127 via MIDI)
• Web-based editor for editing presets and accessing hidden parameters
• Filter cutoff can be modulated by envelope or LFO (via editor, saved to preset)
Designed and assembled in USA. Requires a 9V 250 mA center negative power supply (not included).
MORE»
| List | $329.00 |